ProStart CT-3271 User's Guide download pdf (Page 3)

Quick installation Guide P.3

PROGRAMMING THE TRANSMITTER TO THE MODULE

1. In programming mode (page 2) - the parking lights will stay on for up to 20 seconds.

2. Before the lights go out, turn the ignition key to the Ignition On (Run) position and immediately to the OFF position.

3. Press and hold the BUTTON and keep it down until the parking lights flash 5 times quickly.

4. The transmitter has been stored in memory. Close the hood to end the procedure. Each unit can store 4 remotes in its

memory.

5. You have 20 more seconds to select one of the sub-menus if needed.

ENTERING PROGRAMMING OPTIONS

1. In programming mode (page 2)



the parking lights will stay on for up to 20 seconds.

2. Before the lights go out, press and hold the brake pedal and then press one of the following buttons.

x BUTTON to access mode 1;

x BUTTON to access mode 2;

3. The parking lights will flash once or twice to confirm entry into a mode.

4. Release the brake pedal.

Once the desired mode has been selected, the unit will fall (by default) into function #1 of that mode; you can now select the

option you want in function 1. Once this option has been chosen, the unit will move on to function 2 of the mode selected, and

so on.

x BUTTON to access option 1;

x BUTTON to access option 2;

x & BUTTONS to access option 3

5. You have 20 more seconds to select one of the sub-menus if needed.

PROGRAMMING OPTIONS

MODE 1

* INDICATES DEFAULT SETTING

FUNCTION 1 – Ignition-controlled door locks

OPTION 1* Ignition lock DISABLED

OPTION 2 Ignition lock ENABLED

FUNCTION 2 – Secure Lock

OPTION 1* Secure lock DISABLED

OPTION 2 Standard secure lock ENABLED

FUNCTION 3 – Passive / Active arming of the Starter Kill

OPTION 1* Starter Kill Passive arming (60 sec.). Will arm 60 sec. after ignition OFF.

OPTION 2 Starter Kill Active arming (only arm after LOCK is pressed)

OPTION 3 Starter Kill Passive arming (60 sec.). Note: When SK is armed, pressing will produce

an UNLOCK output when MODE 2, FUNCTION 6, OPTION 1 is enabled.

FUNCTION 4 – Door lock / unlock pulse timing

OPTION 1* 7/10-sec. lock / unlock pulses

OPTION 2 4-sec. lock / unlock pulses

OPTION 3 7/10-sec. lock pulse and two ¼ -sec. unlock pulses

FUNCTION 5 – LED flashing

OPTION 1* Enabled (will only flash when ignition is OFF)

OPTION 2 Disabled

OPTION 3 Enabled (will only flash when Starter kill engages (depends on Mode 1,

Function 3 programming)

FUNCTION 6 – Bypass

OPTION 1* Xpresskit

OPTION 2 ADS

OPTION 3 Fortin

FUNCTION 7 – Bypass Type / PTS mode

OPTION 1* Two-Way communication / Push to Start DISABLED (For Xpresskit bypass only)

OPTION 2 One-Way communication / Push to Start DISABLED

OPTION 3 Two-Way communication / Push to Start ENABLED (For Xpresskit bypass only)

OPTION 4 One-Way communication / Push to Start ENABLED

MODE 2

* INDICATES DEFAULT SETTING

FUNCTION 1 – Engine Run Time

OPTION 1 Run time = 3 minutes in gas mode / 8 minutes diesel mode

P.4 Quick Installation Guide

OPTION 2* Run time = 15 minutes in gas mode / 20 minutes diesel mode

OPTION 3 Run time = 25 minutes in gas mode / 30 minutes diesel mode

FUNCTION 2 – Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)

OPTION 1 Idle mode & turbo mode DISABLED (AUTO) / turbo mode DISABLED (MANUAL)

OPTION 2* Idle mode & turbo mode ENABLED (AUTO) / turbo mode DISABLED (MANUAL)

OPTION 3 Idle mode & turbo mode ENABLED (AUTO) / turbo mode ENABLED (MANUAL)

FUNCTION 3 – Engine type and Cold Weather Mode

OPTION 1 Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)

OPTION 2* Gas mode with 3-minute run time in cold weather mode

OPTION 3 Diesel mode with 8-minute run time in cold weather mode (18-sec. wait to start delay)

FUNCTION 4 – Constant Lock/Unlock or Horn output (when Mode2, Function6, Option1 is programmed)

OPTION 1 N/A

OPTION 2* Lock/Unlock constant output when the BUTTON is pressed >3 sec.

OPTION 3 Horn confirmation upon the 1

press of the BUTTON.

FUNCTION 5 – SmartStart™

OPTION 1 SmartStart™ ENABLED

OPTION 2* SmartStart™ DISABLED

FUNCTION 6 – Remote functions

OPTION 1 Button = Lock/Unlock, Button = Start/Stop, & Buttons = Trunk

OPTION 2* Button = Stop, Button = Start, & Buttons = Trunk

FUNCTION 7 – Ready Mode Option / Hybrid option

OPTION 1 Enabled by handbrake

OPTION 2* Enabled by remote

OPTION 3 Hybrid option ENABLED

SETTING UP THE TACH

VIRTUAL TACH ADJUSTMENT

Warning: For automatic transmissions only.

Virtual Tach System combines the latest microcontroller technology and a complex algorithm that took years to develop. VTS is

able to effectively monitor the engine starting sequence and release the starter at the right time without physically connecting

the tach wire to the remote starter. The VTS constantly monitors the data and readjusts itself automatically in order to maximize

its capability to start the engine properly in any weather or deteriorating battery condition.

OPTIONAL TIME DELAY ADJUSTMENT IN VIRTUAL TACH SYSTEM

Follow these steps to program crank time adjustment, if needed:

1. In programming mode (page 2).

2. Before the lights go out, press and hold the brake pedal and press the BUTTON and BUTTONS simultaneously

 the parking lights will flash 4 times. Do not release the brake pedal.

3. Press the BUTTON if you wish to increase the time delay or the BUTTON if you want to decrease it. The time

delay will be increased or decreased by 50 ms and the parking lights will flash once every time the BUTTON or

the BUTTON is pressed.

4. Press the and BUTTONS to save the settings you have entered.

5. Release the brake pedal – the time delay programming is now complete.

MULTI-SPEED TACH PROGRAMMING

1. In programming mode (page 2).

2. Before the lights go out, press and hold the brake pedal and press the and BUTTONS simultaneously  the

parking lights will flash 4 times. At that point, release the brake pedal.

3. Start up the engine and allow the vehicle to reach regular engine idle speed.

4. Once the engine is running at normal idle speed, press the brake pedal and keep it down until you hear the parking lights

output click 5 times.

5. Release the brake pedal the tach programming is now complete.

Caution! – Tach jumper settings:

Some new vehicles have a higher TACH voltage threshold, which would fall out of the normal TACH trigger circuit of the remote

car starter. Changing the jumper to TACH Threshold HIGH will allow the module to properly detect the TACH signal. BUT, if

you are having trouble with the TACH, please call our tech support team. Problems requiring changing the TACH jumper

settings are very rare.

1 2 3 4

Comments to this Manuals

No comments

ProStart CT-3271 User's Guide Page 3

Comments to this Manuals

Related products and manuals for Remote starters ProStart CT-3271