ProStart CT-3371 Installation Guide

Doc#: 091023 Rev: 2.1 © 2009 CT-3371 -CC- Canada 4BUTTONMANUAL/AUTOMATICTRANSMISSIONREMOTESTARTERWITHVIRTUALTACHSYSTEM(ASP

P.10 Installation guide Note: In the next two systems a Relay in the vehicle interrupts the start wire between the Ignition switch and the starter mo

Installation guide P.11 HarnessDescriptionWhen connecting the Module, it is important to make sure the connector with the Ground wire is connected f

P.12 Installation guide 5PinSecondaryHarnessWire Description 1 BLACK (–) Chassis ground input This wire must be connected to bare, unpainted met

Installation guide P.13 Wire Description 5 WHITE / GREEN (–) Disarm output 500 mA ground output when the button is pressed. This wire is for disa

P.14 Installation guide Wire Description 12 YELLOW (+) Glow-plug input This positive input will monitor the Glow Plug Light in Diesel Mode: it will

Installation guide P.15 3pinHarnessWire Description 1 GRAY/ LIGHT BLUE N/A 2 BLUE / WHITE (–) AUX 1 Output Programmable 500 mA negative output. 3

P.16 Installation guide ManualorAutomaticTransmissionThis module may be installed on vehicles with manual or automatic transmissions. It is origi

Installation guide P.17 EnteringProgrammingModeThis allows the installer to program the unit. Once the system is in programming mode, the installer

P.18 Installation guide Note: For vehicles that require the ignition to be turned ON to activate the brake, follow these steps: a. After flashing th

Installation guide P.19 Programmingoption MODE 1 (* indicates default setting) FUNCTION 1 – Ignition-controlled door locks OPTION 1* Ignition-co

P.2 Installation guide Table of Contents Introduction ...

P.20 Installation guide VirtualTachSystemVirtual Tach System combines the latest microcontroller technology and a complex algorithm that took year

Installation guide P.21 5. Once the engine is running at normal idle speed, press the brake pedal and keep it down until you hear the parking lights

P.22 Installation guide • to lock the doors and shut down the engine; • to unlock the doors and shut down the engine; • to shut down the engine

Installation guide P.23 • The Starter Kill will automatically rearm itself after 1 minute (by default) or 3 minutes (if configured this way) if no do

P.24 Installation guide LEDFlashing1. Enabled without Starter kill: The LED will only flash if IGN is OFF 2. Disabled: LED flashing is disabled a

Installation guide P.25 5. The engine will shut down after 60 seconds. If your vehicle has a manual transmission, follow all steps of the Ready Mode

P.26 Installation guide is held down (maximum of 15 seconds). This negative pulse can be configured to activate certain functionalities such as

Installation guide P.27 ParkinglightsflashessummarytableParking lights flashes Description 1 • Doors locked. • Trunk released. • Enable L

P.28 Installation guide TroubleshootingPoorTransmittingRangeIn order to ensure optimal range, the antenna should be installed at least 7.5 cm

Installation guide P.29 TroubleshootingQ&AThe following are some common installation related issues. A problem or symptom is given and then p

Installation guide P.3 IntroductionThis is a state-of-the-art remote car starter system. The system is packed with advanced features such as priority

P.30 Installation guide • Does it have more then one accessory? 12. The car starts, the heater works but not the air conditioning system. • Missin

P.4 Installation guide InstallationPointstoRemember• On vehicles with a manual transmission, always ensure that all door pins are monitored by t

Installation guide P.5 InstallationOrderThe following is a suggested order for the Installation procedure. It is intended as a guide for novices, to

P.6 Installation guide ♦ With the engine compartment wires out the way, you can begin making the connections in the passenger compartment. Strip abou

Installation guide P.7 Quenching Diodes It was said earlier that a relay energizes itself by applying positive from the battery to either 85 or 86 and

P.8 Installation guide The Relay Connections 85: Connects to the +12 volt park light output from the remote start module. This becomes the positive s

Installation guide P.9 Strengthening Current: Example: Strengthening an output Problem: A vehicle has a negative (-) trigger trunk release wire. The m